Rubber sheet
The rubber membrane is adhered or fastened with as few seams as possible.
Flat Roofing
Rubber Roof Installation Fairfield, NJ
A roofer in Fairfield can install a rubber roof by laying EPDM membrane in wide sheets over insulation and a cover board, bonding or fastening it down and sealing every seam with primer and tape, and explain each choice before the sheet is rolled out. Call (973) 858-9960 to reach a local roofer.
A true rubber roof is EPDM, a synthetic rubber membrane used on flat and low slope roofs for decades. EPDM is sold in wide rolls, typically 45 or 60 mil thick, and it stretches and recovers as the roof moves through hot and cold seasons. Its seams are joined with primer and tape instead of hot air.
Attachment method shapes the rest of the installation. Fully adhered roofs bond the whole sheet to the cover board with adhesive, mechanically attached roofs use plates and fasteners along the seams and ballasted roofs hold a loose sheet down with river stone. For homes, adhered EPDM is the most common choice.
Thickness and color are the next choices. Sixty mil EPDM costs a little more than 45 mil but resists punctures better and lasts longer. Black is standard and holds heat, while white reflects it. Where the rubber meets a shingled roof or the house wall, the tie-in detail matters as much as any of these choices.
Depending on what the roofer finds, rubber roof installation in Fairfield, NJ can go hand in hand with rubber roof repair and flat roof installation.
Need rubber roof installation in Fairfield? Call (973) 858-9960 to reach a nearby roofing contractor.
Call nowThe process
What happens during a rubber roof installation
Each layer is set up to give the membrane a smooth, solid base.
Deck prep
The roofer checks the deck for rot, gaps and loose sheets and confirms the roof has enough slope to drain. A tear-off comes first on existing roofs.
Add the cover board
Polyiso insulation and a cover board create a flat, firm base for the rubber. Low spots can be corrected with tapered insulation.
Sheet layout
The EPDM is unrolled, positioned and left to relax so wrinkles flatten before any adhesive goes on. Laps are arranged so water flows over them.
Bond the membrane
Bonding adhesive is rolled onto both the cover board and the underside of the rubber, then the sheet is folded back down and broomed smooth. Each half gets the same treatment in turn. Brooming from the middle outward pushes trapped air to the edges.
Seal the seams
Seam areas are cleaned and primed, then seam tape is applied and rolled firmly with a seam roller. Exposed edges get lap sealant.
Finish the edges
Flashing goes up walls and around curbs, with boots at pipes and new edge metal at the perimeter. Termination bar and counter flashing seal the wall edge. A final walk checks every seam with a probe before the job is closed out.
What is included
Parts of a new EPDM roof
Deck preparation
The base is cleared and checked so the roof sits on solid wood.
Seams
Laps are joined with seam tape for a lasting bond.
Insulation
A cover board protects the insulation under the rubber.
Flashing
Walls, curbs, pipes and edges are flashed with materials made for EPDM.
Related service
EPDM Roof Installation Fairfield, NJ
Installing EPDM well comes down to preparation, seams and flashing. Rushing the adhesive, skipping primer or leaving wrinkles under the sheet are the common mistakes. Installers work in dry weather so the bond holds. Different adhesives may be used in the field and at the flashings, each matched to the job it does.
A good Fairfield installer also plans for movement. Securing the membrane at the edges and flashing corners correctly prevents later tears. Ask about edge securement before work starts.
Local help
Rubber Roof Installation Near Me
In Fairfield, EPDM is a popular choice for low slope roofs on additions and attached garages. Across Fairfield and nearby towns like Pine Brook, Lincoln Park, Caldwell and Towaco, EPDM handles storms, sun and cold well when it is installed with good seams and drainage, and the right installer makes a big difference.
Need rubber roof installation around Fairfield? Call (973) 858-9960 for a Fairfield roofer who serves the towns around it too.
How the weather here affects roofs around Fairfield
Cold winters bring snow, ice and a long stretch of freezing nights. When warm attic air melts the snow, the meltwater runs down and freezes again at the eaves, building ice dams that push water up under the shingles. Coastal storms and heavy spring rain drive water sideways into flashing, valleys and old chimneys. That is why roof repair in Fairfield is busiest after a hard winter and before the next one.
Why call
Why fix it now
Smaller repairs
Small roof problems caught early usually stay small repairs.
Roofers who know Fairfield
Local roofers see the same roofs and storm damage across Fairfield and nearby towns.
Know what happens next
Ask your questions before you agree to anything.
Common questions about rubber roof installation
What color EPDM is best?
Black and white each have their place. White helps in sunny climates, and black is common where winters are long. Talk through the choice with a roofer.
Is it possible to install EPDM over the old roof?
EPDM can sometimes go over an existing roof. Codes generally allow one recover over a dry, sound roof. Otherwise, a tear-off is needed. The roofer tests the old roof for moisture before recommending a recover.
How long does a new rubber roof last?
Rubber roofs often last decades. Regular inspections help it reach its full life. Small repairs are easy to make.
Is a rubber roof the same as TPO?
The two are different materials. EPDM uses taped seams and stays flexible in cold, and TPO uses welded seams and reflects heat. Both are common on flat roofs.
Which EPDM thickness should I choose?
Most residential EPDM is 45 or 60 mil. Sixty mil resists punctures better and lasts longer, which helps on roofs with foot traffic or hail. Even thicker sheets are available for demanding roofs.
More questions? Call (973) 858-9960
Often needed together
Rubber Roof Repair
EPDM rubber roof repairs done with primer, cover tape and lap sealant made for rubber, after the real leak point is found.
Learn moreFlat Roof Installation
New flat roofs built with real slope, insulation, a cover board and a membrane suited to the building, planned around how the roof will be used.
Learn moreTPO Roofing
Heat-welded TPO membrane for flat and low-slope roofs, with seams welded into one watertight sheet.
Learn moreFlat Roof Replacement
Full replacement of failing flat roofs, with a moisture survey deciding tear-off or recover, with tapered insulation where water used to sit.
Learn more
Looking for something else?
See all roofing servicesNeed rubber roof installation in Fairfield, NJ?
Call now for Fairfield rubber roof installation and help in the towns around it.